|
Articles Published In Refereed Journals: 1. Abedian, A., Szyszkowski, W., "Influence of the free surface on the thermal stresses in unidirectional composites", Composites Part A, 28A, pp. 573-579, 1997. 2. Abedian, A., Szyszkowski, W., Yannacopoulos, S., "Residual thermal stresses in metallic and inter metallic matrix composites after cooling from processing temperature", Composites Technology & Research, Vol. 20, No. 3, pp. 161-169, 1998. 3. Abedian, A., Szyszkowski, W., Yannacopoulos, S., "Effects of surface geometry of composites on thermal stress distribution: a numerical study", Composites Science and Technology, Vol. 59, pp. 41-54, 1999. 4. Abedian, A., Yannacopoulos, S., Szyszkowski, W., "Effects of free surface geometry on damage initiation in unidirectional composites due to temperature cycling: an Experimental investigation", Canadian Metallurgical Quarterly, Vol. 39, No. 1, pp. 99-112, 2000. 5. Abedian, A., Szyszkowski, W., Yannacopoulos, S., "Analysis of creep effects on the residual stress in SCS-6/Ti-6Al-4V composites using FEM", Thermal Stresses, Vol. 24, pp. 1-17, 2001. 6. Mondali, M., Abedian, A., Adibnazari, S., "FEM study of the second stage creep behavior of Al6061/SiC metal matrix composite", Computational Materials Science, Vol. 34, pp. 140-150, 2005. 7. Abedian, A., Ghiasi, M.H., Dehghan-Manshadi, B., "Effects of a linear-exponential penalty function on the GA's Efficiency in Optimization of laminated composite panel", International Journal of Computational Intelligence (IJCI), Vol. 2, No. 1, pp. 5-11, 2005. 8. Abedian, A., Adibnazari, S., Rashidi-Moghadam, A., "FEM elasto-plastic analysis of a new manufacturing method for covering the free surface of unidirectional composites", Computational Materials Science, Vol. 36, pp. 411-424, 2006. 9. Abedian, A., Ghiasi, M.H., Dehghan-Manshadi, B., "An introduction to a new criterion proposed for stopping GA optimization process of a laminated composite plate", Journal of Aerospace Science and Technology (JAST), Vol. 3, No. 4, pp. 167-176, 2006. 10. Dehghan-Manshadi, B., Mahmudi, H., Abedian, A., Mahmudi, R., "A novel method for materials selection in mechanical design: combination of non-linear normalization and a modified digital logic method", Materials & Design, Vol. 28, pp. 8-15, 2007. 11. Abedian, A., Mondali, M., Pahlavanpour, M., "Basic modifications in 3D micromechanical modeling of short fiber composites with bonded and debonded fiber end", Computational Materials Science, Vol. 40, pp. 421-433, 2007. 12. Zabihpour, M., Adibnazari, S., Moslemian, R., Abedian, A., "Mechanisms of fatigue damage in foam core sandwich composites with unsymmetrical Carbon/Glass Face Sheets", Journal of Reinforced Plastics & Composites, Vol. 26, pp. 1831-1842, 2007. 13. Sarfaraz-Kahbaz, R., Dehghan-Manshadi, B., Abedian, A., Mahmudi, R., "A simplified fuzzy logic approach for materials selection in mechanical engineering design", Materials & Design, 2008 (Accepted). 14. Sarfaraz-Khabaz, R., Dehghan-Manshadi, B., Abedian, A, "Non-linear analysis of FGM plates under pressure loads using the higher-order shear deformation theories", Composite Structures, 2008 (Accepted). 15. Mondali, M., Abedian, A., Ghavami, A."A new analytical shear-lag based model for prediction of the steady state creep deformations of short fiber composites", Materials & Design, 2008 (Accepted). |